관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
분야 | ISO/TC 98/SC 3 : Loads, forces and other actions |
---|---|
적용범위 | ISO 3010:2017 (including both the super structure and foundation) and other structures. ISO 3010:2017 is not applicable to certain structures, such as bridges, dams, geotechnical works and tunnels, although some of the principles can be referred to for the seismic design of those structures. ISO 3010:2017 is not applicable to nuclear power plants, since these are dealt with separately in other International Standards. In regions where the seismic hazard is low, methods of design for structural integrity can be used in lieu of methods based on a consideration of seismic actions. ISO 3010:2017 is not a legally binding and enforceable code. It can be viewed as a source document that is utilized in the development of codes of practice by the competent authority responsible for issuing structural design regulations. NOTE 1 This document has been prepared mainly for new engineered structures. The principles are, however, applicable to developing appropriate prescriptive rules for non-engineered structures (see Annex N). The principles could also be applied to evaluating seismic actions on existing structures. NOTE 2 Other structures include self-supporting structures other than buildings that carry gravity loads and are required to resist seismic actions. These structures include seismic force-resisting systems similar to those in buildings, such as a trussed tower or a pipe rack, or systems very different from those in buildings, such as a liquid storage tank or a chimney. Additional examples include structures found at chemical plants, mines, power plants, harbours, amusement parks and civil infrastructure facilities. NOTE 3 The level of seismic hazard that would be considered low depends not only on the seismicity of the region but also on other factors, including types of construction, traditional practices, etc. Methods of design for structural integrity include nominal design horizontal forces (such as an equivalent static loading determined from a simplified equivalent static analysis) which provide a measure of protection against seismic actions. |
국제분류(ICS)코드 |
91.080.01 : 건축 구조 일반
91.120.25 : 지진 및 진동 방지 |
페이지수 | 60 |
Edition | 3 |
No. | 표준번호 | 표준명 | 발행일 | 상태 |
---|---|---|---|---|
1 | ISO 3010:2017 | Bases for design of structures — Seismic actions on structures | 2017-03-30 | 표준 |
2 | ISO 3010:2001 | Basis for design of structures — Seismic actions on structures | 2001-12-20 | 구판 |
3 | ISO 3010:1988 | Bases for design of structures — Seismic actions on structures | 1988-07-07 | 구판 |
관련상품이 존재하지 않습니다.
IEC TS 62600-2:2019 - Marine energy - Wave, tidal and other water current converters - Part 2: Marine energy systems - Design requirements 상세보기
IEC TS 62600-20:2019 - Marine energy - Wave, tidal, and other water current converters - Part 20: Design and analysis of an Ocean Thermal Energy Conversion (OTEC) plant - General guidance 상세보기
IEC TS 62600-1:2011+AMD1:2019 CSV - Marine energy - Wave, tidal and other water current converters - Part 1: Terminology 상세보기
IEC TS 62600-201:2015 - Marine energy - Wave, tidal and other water current converters - Part 201: Tidal energy resource assessment and characterization 상세보기
IEC TS 62600-10:2015 - Marine energy - Wave, tidal and other water current converters - Part 10: Assessment of mooring system for marine energy converters (MECs) 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기