관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
표준
판매
Rolling bearings — Methods for calculating the modified reference rating life for universally loaded bearings
| 분야 | ISO/TC 4/SC 8 : Load ratings and life |
|---|---|
| 적용범위 | ISO/TS 16281:2008 contains recommendations for the calculation of the modified reference rating life taking into consideration lubrication, contamination and fatigue load limit of the bearing material, as well as tilting or misalignment, operating clearance of the bearing and internal load distribution on rolling elements. The calculation method provided in ISO/TS 16281:2008 covers influencing parameters additional to those described in ISO 281. The directions and limitations given in ISO 281 apply to ISO/TS 16281:2008. The calculation methods pertain to the fatigue life of the bearings. Other mechanisms of failure, like wear or microspalling (gray staining), lie outside the scope of ISO/TS 16281:2008. ISO/TS 16281:2008 applies to tilted single-row radial ball bearings, subjected to radial and axial load, and with radial clearance and tilt taken into account. It also applies to tilted single-row roller bearings, subjected to pure radial load and with radial clearance, edge stress and tilt taken into account. References to methods for the analysis of the internal load distribution under general load are given. The analysis of internal load distribution and modified reference rating life for multi-row bearings or bearings of a more complex geometry can be derived from the equations given in ISO/TS 16281:2008. For these bearings, the load distribution for each individual row has to be considered. ISO/TS 16281:2008 is primarily intended to be used for computer programs and together with ISO 281 covers the information needed for life calculations. For accurate life calculations under the operating conditions specified above, it is recommended that either ISO/TS 16281:2008 or advanced computer calculations provided by bearing manufacturers, for determining the dynamic equivalent reference load under different loading conditions, be used. |
| 국제분류(ICS)코드 | 21.100.20 : 구름 베어링 |
| 페이지수 | 20 |
| Edition | 1 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ISO/TS 16281:2008 | Rolling bearings — Methods for calculating the modified reference rating life for universally loaded bearings | 2008-05-27 | 표준 |
관련상품이 존재하지 않습니다.
ISO 6336-5:2016 - Calculation of load capacity of spur and helical gears — Part 5: Strength and quality of materials 상세보기
ISO 6336-1:2019 - Calculation of load capacity of spur and helical gears — Part 1: Basic principles, introduction and general influence factors 상세보기
ISO 6336-2:2019 - Calculation of load capacity of spur and helical gears — Part 2: Calculation of surface durability (pitting) 상세보기
ISO 6336-3:2019 - Calculation of load capacity of spur and helical gears — Part 3: Calculation of tooth bending strength 상세보기
ISO 6336-6:2019 - Calculation of load capacity of spur and helical gears — Part 6: Calculation of service life under variable load 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
