관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
표준
판매
Plastics — Determination of resistance to environmental stress cracking (ESC) — Part 6: Slow strain rate method
| 분야 | ISO/TC 61/SC 6 : Ageing, chemical and environmental resistance |
|---|---|
| 적용범위 | ISO 22088-6:2006 describes a procedure for assessing the environmental stress cracking (ESC) susceptibility of polymeric materials in chemical environments by slowly increasing the strain applied to a tensile specimen at a constant rate. It is applicable to test specimens prepared by moulding and/or machining and can be used to assess the relative ESC susceptibility of a material exposed to different environments or the relative ESC susceptibility of different plastics exposed to a specific environment. This is essentially a ranking test and is not intended for the provision of design data. The principle advantage of the test compared with the test methods described in Parts 2 to 5 of ISO 22088 is the rapidity with which the ESC susceptibility of a particular polymer/environment combination can be assessed. |
| 국제분류(ICS)코드 | 83.080.01 : 플라스틱 일반 |
| 페이지수 | 9 |
| Edition | 1 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ISO 22088-6:2006 | Plastics — Determination of resistance to environmental stress cracking (ESC) — Part 6: Slow strain rate method | 2006-08-08 | 표준 |
ISO 22088-5:2006 - Plastics — Determination of resistance to environmental stress cracking (ESC) — Part 5: Constant tensile deformation method 상세보기
ISO 22088-1:2006 - Plastics — Determination of resistance to environmental stress cracking (ESC) — Part 1: General guidance 상세보기
ISO 22088-2:2006 - Plastics — Determination of resistance to environmental stress cracking (ESC) — Part 2: Constant tensile load method 상세보기
ISO 22088-3:2006 - Plastics — Determination of resistance to environmental stress cracking (ESC) — Part 3: Bent strip method 상세보기
ISO 22088-4:2006 - Plastics — Determination of resistance to environmental stress cracking (ESC) — Part 4: Ball or pin impression method 상세보기
ISO 22088-3:2006 - Plastics — Determination of resistance to environmental stress cracking (ESC) — Part 3: Bent strip method 상세보기
ISO 22088-2:2006 - Plastics — Determination of resistance to environmental stress cracking (ESC) — Part 2: Constant tensile load method 상세보기
ISO 22088-1:2006 - Plastics — Determination of resistance to environmental stress cracking (ESC) — Part 1: General guidance 상세보기
ISO 16241:2005 - Notch tensile test to measure the resistance to slow crack growth of polyethylene materials for pipe and fitting products (PENT) 상세보기
ISO 15306:2003 - Glass-reinforced thermosetting plastics (GRP) pipes — Determination of the resistance to cyclic internal pressure 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
