관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
표준
판매
Design of steel structures
| 분야 | |
|---|---|
| 적용범위 | Preface This is the eighth edition of CSA S16, Design of steel structures. It supersedes the previous limit states editions published in 2009, 2001, 1994, 1989, 1984, 1978, and 1974. These limit states design editions were preceded by seven working stress design editions published in 1969, 1965, 1961, 1954, 1940, 1930, and 1924. The 1969 working stress design edition was withdrawn in 1984, from which point the design of steel structures in Canada has been carried out using limit states design principles.? This Standard is appropriate for the design of a broad range of structures. It sets out minimum requirements and is expected to be used only by engineers competent in the design of steel structures.? The following is a list of some of the more important changes made in this edition:? a) Clause 1.4 specifically prohibits the use of other standards for fabrication, erection and inspection.? b) The definition of "snug-tightness" has been clarified.? c) Information required on design documents has been augmented.? d) ASTM grades A500/A500M, A1085 and A913/A913M have been added as permissible steel grades for design.? e) The fire endurance design requirements have been restated to be in compliance with the NBCC.? f) Requirements under impulse loading have been added.? g) The initial misalignment of members at brace points has been clarified.? h) A calculation for the net area of a slotted HSS member has been given.? i) The minimum b/t for bearing stiffeners has been added.? j) The clause permitting a joist manufacturer to determine the joist resistance by testing has been removed.? k) Provisions for column stiffeners opposite a rigidly connected beam by bolting have been provided.? l) Requirements for zinc-aluminum coated assemblies have been incorporated.? m) The use of plate washers in lieu of hardened washers is permitted in oversize or slotted holes.? n) The use of non-matching electrodes is permitted with reference to W59 for locations where this is permitted.? o) Clause 24 that referred to joint surface conditions for field welding in the previous edition has been removed and is now covered in CSA W47.1.? p) The factored resistance of anchor rods in bearing has been referred to CSA A23.3 to be consistent with other Canadian design standards.? q) A clarification on fatigue calculations has been made to include bending moments due to joint eccentricities.? r) An upper limit on the design force of single-storey buildings' roof diaphragms has been provided.? s) A minimum Charpy V-notch value has been specified for weld of primary members and connections.? t) A maximum sulfur content for ASTM A913 used in seismic-resisting systems is specified.? u) Additional criteria for joint connections have been added to ductile moment-resisting frames, limited ductility moment-resisting frames, and moderately ductile concentrically braced frames.? v) The design of link beams for ductile eccentrically braced frames has been expanded.? w) Detailing information for limited ductility plate walls has been given.? x) Annex K Structural design for fire conditions has been updated.? y) The clauses related to pin-connected members have been revised to clarify the net section and resistance requirements.? A commentary on this Standard, prepared by the Canadian Institute of Steel Construction with contributions from many members of the Technical Committee, comprises Part 2 of the Institute's Handbook of Steel Construction.? This Standard is intended to be used with the provisions of the 2015 edition of the National Building Code of Canada (NBCC), specifically Clause 7, which references the NBCC for load factors, load combinations, and other loading provisions.? Scope? 1.1 General This Standard provides rules and requirements for the design, fabrication, and erection of steel structures. The design is based on limit states. The term "steel structures" refers to structural members and frames that consist primarily of structural steel components, including the detail parts, welds, bolts, or other fasteners required in fabrication and erection. This Standard also applies to structural steel components in structures framed in other materials. The clauses related to fabrication and erection serve to show that design is inextricably a part of the design-fabrication-erection sequence and cannot be considered in isolation. For matters concerning standard practice pertinent to the fabrication and erection of structural steel not covered in this Standard, see Annex A.? 1.2 Requirements Requirements for steel structures such as bridges, antenna towers, offshore structures, and cold-formed steel structural members are given in other CSA Group Standards.? 1.3 Application This Standard applies unconditionally to steel structures, except that supplementary rules or requirements might be necessary for? a) unusual types of construction b) mixed systems of construction c) steel structures that: i) have great height or spans ii) are required to be movable or be readily dismantled iii) are exposed to severe environmental conditions iv) are exposed to severe loads such as those resulting from vehicle impact or explosion v) are required to satisfy aesthetic, architectural, or other requirements of a non-structural nature vi) employ materials or products not listed in Clause 5 vii) have other special features that could affect the design, fabrication, or erection d) tanks, stacks, other platework structures, poles, and piling e) crane-supporting structures 1.4 Other standards The use of other standards for the design, fabrication, erection, and/or inspection of members or parts of steel structures is neither warranted nor acceptable except where specifically directed in this Standard. The design formulas provided in this Standard may be supplemented by a rational design based on theory, analysis, and engineering practice acceptable to the regulatory authority, provided that nominal margins (or factors) of safety are at least equal to those intended in the provisions of this Standard. The substitution of other standards or criteria for fabrication, erection, and/or inspection is expressly prohibited unless specifically directed in this Standard.? 1.5 Terminology In this Standard, "shall" is used to express a requirement, i.e., a provision that the user is obliged to satisfy in order to comply with the standard; "should" is used to express a recommendation or that which is advised but not required; and "may" is used to express an option or that which is permissible within the limits of the Standard.? Notes accompanying clauses do not include requirements or alternative requirements; the purpose of a note accompanying a clause is to separate from the text explanatory or informative material.? Notes to tables and figures are considered part of the table or figure and may be written as requirements.? Annexes are designated normative (mandatory) or informative (non-mandatory) to define their application. ? |
| 국제분류(ICS)코드 | |
| 페이지수 | 255 |
| Edition |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | CSA S16:24 | Design and construction of steel structures | 2024-01-01 | 표준 |
| 2 | CSA S16:19 | Design of steel structures | 2019-01-01 | 표준 |
| 3 | S16-14 (R2019) | Design of steel structures | 2014-01-01 | 표준 |
관련상품이 존재하지 않습니다.
N286.3-99 (R2004) - Construction Quality Assurance for Nuclear Power Plants Published by CSA Group in 1999, Reaffirmed in 2004, Withdrawn 상세보기
C22.2 NO. 178-1978 (R2006) - Automatic Transfer Switches 0 Edition, Published by CSA Group in 1978, Reaffirmed in 2006, Withdrawn 상세보기
SPE-2000-94 - Guide for Electrical Equipment for Installation and Use in Canada 상세보기
CAN/CSA-C867.2-09 (R2014) - Performance of decorative light strings.Published by CSA Group in 2009, Reaffirmed in 2014, Withdrawn 상세보기
N292.0-14/N292.3-14 PACKAGE - Consists of N292.0-14, General principles for the management of radioactive waste and irradiated fuel and N292.3-14, Management of low- and intermediate-level radioactive waste 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
