관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
표준
절판(중지)
Manually operated valves for use in gaseous hydrogen vehicle fueling stations
| 언어 | 제공형태 | 판매가격 | 선택 |
|---|---|---|---|
|
영어 |
보안PDF |
517,200원 |
|
| 분야 | |
|---|---|
| 적용범위 | Preface This is the first edition of ANSI/CSA HGV 4.6-2013, Manually Operated Valves for Use in Gaseous Hydrogen Vehicle Fueling Stations. It supersedes the previous edition published in 2009. Scope This Standard contains safety requirements for the material, design, manufacture and testing of manually operated valves for gaseous hydrogen vehicle fueling stations. This Standard applies to newly manufactured valves. 1.1 This Standard does not apply to: a) Fuel storage container shut-off valves connected directly to the storage container as covered by the appropriate standards (e.g., UL 1769, CGA V-9, etc.). b) Fueling nozzle valves as covered by the Standard for Compressed Hydrogen Surface Vehicle Refueling Connection Device, SAE J2600 or ISO 17268. c) Does not apply to pressure Class 150 hardware (under 2 MPa (300 psi)) 1.1.1 All references to pressure throughout this document are to be considered gauge pressures unless otherwise specified. 1.1.2 All dimensions used in this standard are in metric units [International System of Units (SI)], unless otherwise specified. If a value for a measurement, as given in this standard, is followed by an equivalent value in other units, the first stated is to be regarded as the specification. 1.2 This Standard contains SI (Metric) corresponding to the yard/pound quantities, the purpose being to allow the standard to be used in SI (Metric) units. (Standard for use of the International System of Units (SI): The Modern Metric System, IEEE/ASTM SI I0 or ISO 80000-1:2009 Quantities and units- Part 1: General are used as a guide in making metric conversion from yard/pound quantities.) If a value for a measurement and a corresponding value in other units are stated, the first stated value is to be regarded as the requirement. The given corresponding value may be approximate. If a value for a measurement and a corresponding value in other units are both specified as a quoted marking requirement, the first stated unit, or both shall be provided. |
| 국제분류(ICS)코드 | |
| 페이지수 | 29 |
| Edition |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|
관련상품이 존재하지 않습니다.
ANSI/CSA HGV 4.4-2013 (R2018) - Breakaway devices for compressed hydrogen dispensing hoses and systems 상세보기
ANSI/CSA HGV 4.2-2013 (R2019) - Hoses for compressed hydrogen fuel stations, dispensers and vehicle fuel systems 상세보기
ANSI/CSA HGV 4.7-2013 (R2018) - Automatic valves for use in gaseous hydrogen vehicle fueling stations 상세보기
ANSI/CSA HGV 4.8-2012 (R2023) - Hydrogen gas vehicle fueling station compressor guidelines 상세보기
ANSI/CSA HGV 4.10-2012 (R2019) - Fittings for compressed hydrogen gas and hydrogen rich gas mixtures 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
