관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
표준
판매
Design of concrete structures
| 분야 | |
|---|---|
| 적용범위 | Preface This is the fifth edition of CSA A23.3, Design of concrete structures. It supersedes the previous editions published in 1994, 1984, 1977 (metric) and 1973 (imperial), and 1959. This Standard is intended for use in the design of concrete structures for buildings in conjunction with CSA A23.1-04/A23.2-04, Concrete materials and methods of concrete construction/Methods of test and standard practices for concrete, and CSA A23.4, Precast concrete - Materials and construction (under preparation). Scope 1.1 General This Standard specifies requirements, in accordance with the National Building Code of Canada, for the design and strength evaluation of (a) structures of reinforced and prestressed concrete; (b) plain concrete elements; and (c) special structures such as parking structures, arches, tanks, reservoirs, bins and silos, towers, water towers, blast-resistant structures, and chimneys. Note: Special requirements for parking structures are specified in CAN/CSA-S413. 1.2 Fire resistance This Standard requires designs to be carried out in accordance with the fire resistance requirements of the applicable building code (see Clause 8.1.2). 1.3 Alternative design procedures Designs that use procedures which are not covered by this Standard but are carried out by a person qualified in the methods applied and provide a level of safety and performance equivalent to designs complying with this Standard are acceptable if carried out by one of the following methods: (a) analysis based on generally established theory; (b) evaluation of a full-scale structure or a prototype by a loading test; or (c) studies of model analogues. 1.4 Terminology In CSA Standards, "shall" is used to express a requirement, i.e., a provision that the user is obliged to satisfy in order to comply with the standard; "should" is used to express a recommendation or that which is advised but not required; "may" is used to express an option or that which is permissible within the limits of the standard; and "can" is used to express possibility or capability. Notes accompanying clauses do not include requirements or alternative requirements; the purpose of a note accompanying a clause is to separate from the text explanatory or informative material. Notes to tables and figures are considered part of the table or figure and may be written as requirements. Annexes are designated normative (mandatory) or informative (non-mandatory) to define their application. 1.5 Units of measurement Equations appearing in this Standard are compatible with the following units: (a) area: mm2 (square millimetres); (b) force: N (newtons); (c) length: mm (millimetres); (d) moment: N.mm (newton millimetres); and (e) stress: MPa (megapascals). Whenever the square root of the concrete strength is determined, the concrete strength and the square root of the concrete strength are both expressed in megapascals. Other dimensionally consistent combinations of units may be used, provided that appropriate adjustments are made to constants in non-homogeneous equations. Note: Some examples of non-homogeneous equations are found in Clauses 12.2.2 and 12.8. ? |
| 국제분류(ICS)코드 | |
| 페이지수 | 352 |
| Edition |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | CSA A23.3:24 | Design of concrete structures | 2024-01-01 | 표준 |
| 2 | CSA A23.3:19 | Design of concrete structures | 2019-01-01 | 표준 |
| 3 | A23.3-14 | Design of concrete structures | 2014-01-01 | 표준 |
| 4 | CAN/CSA-A23.3-04 (R2010) | Design of concrete structures | 2004-01-01 | 표준 |
관련상품이 존재하지 않습니다.
함께 구입한 상품이 존재하지 않습니다.
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
