관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
표준
판매
Information Technology - Telecommunications and Information Exchange Between Systems - Start-Stop Transmission Signal Quality at DTE/DCE Interfaces (Adopted ISO/IEC 7480:1991)
| 분야 | |
|---|---|
| 적용범위 | Scope 1.1 This International Standard specifies signal quality requirements for serial data transmission at the interface between start-stop transmission Data Terminal Equipment (DTE) and Data Circuit-terminating Equipment (DCE). The interface referred to in this International Standard conforms to CCITT Recommend ations V.24 (telephone networks) and X.24 (data networks) as specified in DCEs of the following CCITT Recommendations: ? V.21, V.22, V.22 bis, V.23, V.26 ter, V.32, V.32 bis, X.20, X.20 bis together with V.28 electrical characteristics; X.20 together with V.10 and/or V.11 electrical characteristics. The signal quality requirement is limited to start-stop transmission at the interface with asynchronous DCEs, or with synchronous DCEs operating in asynchronous mode in accordance with CCITT Recommendations V.14 or V.42. Signal quality pertaining to DTEs working in a synchronous mode of operation is not part of this International Standard. This International Standard is also applicable when the interface as specified in the above CCITT Recommendations is provided at the ISDN Reference point R as defined in CCITT Recommendation I.411 and as specified in CCITT Recommendations V.110, V.120 and X.30. 1.2 The signal quality characteristics apply regardless of w hether or not multiplexing equipment is included. They do not apply where there is intermediate equipment and no signal regeneration is provided between interconnected sections. 1.3 This International Standard does not describe the signal quality of the DCE or the line associated with it. Neither does it describe any requirement for an acceptable bit error rate. 1.4 This International Standard does not specify the speed characteristics. The nominal value of the modulation rate and the character interval are application dependent. |
| 국제분류(ICS)코드 | |
| 페이지수 | 18 |
| Edition |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | CAN/CSA-ISO/IEC 7480-95 (R2013) | Information Technology - Telecommunications and Information Exchange Between Systems - Start-Stop Transmission Signal Quality at DTE/DCE Interfaces (Adopted ISO/IEC 7480:1991) | 1995-01-01 | 표준 |
| 2 | ISO/IEC 7480:1991 | Information technology — Telecommunications and information exchange between systems — Start-stop transmission signal quality at DTE/DCE interfaces | 1991-12-19 | 표준 |
| 3 | ISO/IEC 7480:1991 | Information technology - Telecommunications and information exchange between systems - Start-stop transmission signal quality at DTE/DCE interfaces | 1991-12-19 | 표준 |
관련상품이 존재하지 않습니다.
함께 구입한 상품이 존재하지 않습니다.
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
