관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
구판
판매
Design of Below-the-Hook Lifting Devices
| 분야 | |
|---|---|
| 적용범위 | BTH-1 provides minimum structural and mechanical design and electrical component selection criteria for ASME B30.20 below-the-hook lifting devices. The provisions in this Standard apply to the design or modification of below-the-hook lifting devices. Compliance with requirements and criteria that may be unique to specialized industries and environments is outside of the scope of this Standard. Lifting devices designed to this Standard shall comply with ASME B30.20, Below-the-Hook Lifting Devices. B30.20 includes provisions that apply to the marking, construction, installation, inspection, testing, maintenance, and operation of below-the-hook lifting devices. BTH-1 addresses only design requirements. As such, this Standard should be used in conjunction with B30.20, which addresses safety requirements. BTH-1 does not replace B30.20. The design criteria set forth are minimum requirements that may be increased at the discretion of the lifting device manufacturer or a qualified person. Key changes to this revision of BTH-1 include: ? Addition of chapter of requirements for Lifting Magnet Design with additional commentary found in a corresponding new Nonmandatory Appendix ? Addition of design requirements for new Design Category for specialized application in industries that require lifting designs based on a specified larger Design factor ? Addition of new requirements for Member Properties ? Updated Table 3-2.2-1 Limiting Width-Thickness Ratios for Compression Elements BTH-1 and B30.20 are to be used in conjunction with equipment described in other volumes of the ASME B30 series of Safety Standards. Careful application of these Safety Standards will help users to comply with applicable regulations within their jurisdictions, while achieving the operational and safety benefits to be gained from the many industry best-practices detailed in these volumes. Intended for manufacturers, owners, employers, users and others concerned with the specification, buying, maintenance, training and safe use of below-the-hook lifting devices with B30 equipment, plus all potential governing entities. |
| 국제분류(ICS)코드 | |
| 페이지수 | 84 |
| Edition |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASME BTH-1-2023 | Design of Below-the-Hook Lifting Devices | 2023-10-16 | 표준 |
| 2 | ASME BTH-1-2020 | Design of Below-the-Hook Lifting Devices | 2021-06-11 | 구판 |
| 3 | ASME BTH-1-2017 | Design of Below-the-Hook Lifting Devices | 2017-01-01 | 구판 |
| 4 | ASME BTH-1-2014 | Design of Below-the-Hook Lifting Devices (BTH-1 - 2014) | 2014-01-01 | 구판 |
| 5 | ASME BTH-1-2011 | Design of Below-the-Hook Lifting Devices (BTH-1 - 2011) | 2011-01-01 | 구판 |
| 6 | ASME BTH-1-2008 | Design of Below-the-Hook Lifting Devices (BTH-1 - 2008) | 2008-01-01 | 구판 |
| 7 | ASME BTH-1-2005 | Design of Below-the-Hook Lifting Devices (BTH-1 - 2005) | 2005-01-01 | 구판 |
ASME BTH-1-2023 - Design of Below-the-Hook Lifting Devices 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
