관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
구판
판매
Measurement of Liquid Flow in Closed Conduits by Weighing Method (MFC-9M - 1988)
| 분야 | MFC : Flow Measurement |
|---|---|
| 적용범위 | This Standard specifies a method of liquid flow rate measurement in closed conduits by measuring the mass of liquid delivered into a weighing tank in a known time interval. It deals in particular with the measuring apparatus, procedure, and method for calculating the flow rate and the uncertainties associated with the measurement. The method described may be applied to any liquid, provided that its vapor pressure is such that any escape of liquid from the weighing tank by vaporization is not sufficient to effect the required measurement accuracy. Closed weighing tanks and their application to the flow measurement of liquids of high vapor pressure are not considered in this Standard. This Standard considers only the measurement techniques and does not address any possible hazards involved in handling the liquid involved. Theoretically, there is no limit to the application of this method, which is used generally in fixed laboratory installations only. However, for economic reasons, typical hydraulic laboratories using this method can produce accurate flow rates of 500 kg/s (3300 lbm/sec) or less. Owing to its high potential accuracy, this method is often used as a primary method for calibration of other methods or devices for mass flow rate measurement or volumetric flow rate measurement, provided that the density of the liquid is known accurately. It must be ensured that the pipeline is running full with no air or vapor pockets present in the measuring section. |
| 국제분류(ICS)코드 | |
| 페이지수 | 17 |
| Edition |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASME MFC-9M-1988(R2011) | Measurement of Liquid Flow in Closed Conduits by Weighing Method (MFC-9M - 1988) | 1988-01-01 | 구판 |
| 2 | ASME MFC-9M-1988(R2021) | Measurement of Liquid Flow in Closed Conduits by Weighing Method (MFC-9M - 1988) | 1988-01-01 | 표준 |
ASME MFC-2M-1983(R2013) - Measurement Uncertainty for Fluid Flow in Closed Conduits (MFC-2M - 1983) 상세보기
ASME MFC-4M-1986(R2016) - Measurement of Gas Flow by Turbine Meters (MFC-4M - 1986) 상세보기
ASME MFC-7M-1987(R2014) - Measurement of Gas Flow by Means of Critical Flow Venturi Nozzles (MFC-7M - 1987) 상세보기
ASME MFC-9M-1988(R2021) - Measurement of Liquid Flow in Closed Conduits by Weighing Method (MFC-9M - 1988) 상세보기
ASME MFC-10M-2000(R2021) - Method for Establishing Installation Effects on Flow Meters (MFC-10M - 2000) 상세보기
함께 구입한 상품이 존재하지 않습니다.
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
