관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
표준
판매
Standard Test Method for Consolidated Undrained Direct Simple Shear Testing of Fine-Grained Soils
| 분야 | |
|---|---|
| 적용범위 | 1.1?This test method defines equipment specifications and testing procedures for the measurement of constant volume strength and stress-strain characteristics of fine-grained soils after one-dimensional consolidation, using a constant rate of simple shear deformation mode of loading. The constant volume condition is equivalent to the undrained condition for saturated specimens. 1.2?This test method is written specifically for devices that test rectangular parallelepiped or cylindrical specimens. Other more general devices, such as the torsional shear hollow cylinder, may be used to perform consolidated constant volume simple shear tests but are beyond the scope of this test method. 1.3?This test method is applicable to testing intact, laboratory reconstituted, and compacted soils, however, it does not include specific guidance for reconstituting or compacting test specimens. 1.4?It shall be the responsibility of the agency requesting this test to specify the magnitude of the vertical consolidation stress prior to constant volume shear and, when appropriate, the maximum vertical consolidation stress, which will result in an overconsolidated specimen. 1.5?Units?The values stated in SI units are to be regarded as the standard. No other units of measure are included in this standard. Reporting of test results in units other than SI shall not be regarded as nonconformance with this standard. 1.5.1?In the engineering profession it is customary practice to use, interchangeably, units representing both mass and force, unless dynamic calculations (F=Ma) are involved. This implicitly combines two separate systems of units, that is, the absolute system and the gravimetric system. It is scientifically undesirable to combine two separate systems within a single standard. This test method has been written using SI units; however, inch-pound conversions are given in the gravimetric system, where the pound (lbf) represents a unit of force (weight). The use of balances or scales recording pounds of mass (lbm), or the recording of density in lb/ft3 should not be regarded as nonconformance with this test method. 1.6?All observed and calculated values shall conform to the guidelines for significant digits and rounding established in Practice D6026. 1.6.1?The procedures used to specify how data are collected/recorded or calculated in this test standard are regarded as the industry standard. In addition, they are representative of the significant digits that should generally be retained. The procedures used do not consider material variation, purpose for obtaining the data, special purpose studies, or any considerations for the user’s objectives; it is common practice to increase or reduce significant digits of reported data to be commensurate with these considerations. It is beyond the scope of this test standard to consider significant digits used in analysis methods for engineering design. 1.6.2?Measurements made to more significant digits or better sensitivity than specified in this standard shall not be regarded a nonconformance with this standard. 1.7?This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.8?This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
| 국제분류(ICS)코드 | |
| 페이지수 | 10 |
| Edition | 24 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM D6528-24 | Standard Test Method for Consolidated Undrained Direct Simple Shear Testing of Fine-Grained Soils | 2024-07-01 | 표준 |
| 2 | ASTM D6528-24 REDLINE | Standard Test Method for Consolidated Undrained Direct Simple Shear Testing of Fine-Grained Soils | 2024-07-01 | 표준 |
| 3 | ASTM D6528-17 | Standard Test Method for Consolidated Undrained Direct Simple Shear Testing of Fine Grain Soils | 2017-08-01 | 구판 |
| 4 | ASTM D6528-07 | Standard Test Method for Consolidated Undrained Direct Simple Shear Testing of Cohesive Soils (Withdrawn 2016) | 2007-11-15 | 구판 |
| 5 | ASTM D6528-00 | Standard Test Method for Consolidated Undrained Direct Simple Shear Testing of Cohesive Soils | 2000-02-10 | 구판 |
관련상품이 존재하지 않습니다.
함께 구입한 상품이 존재하지 않습니다.
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
