관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
구판
판매
Standard Practice for Extraction of Medical Plastics
| 분야 | |
|---|---|
| 적용범위 | 1.1 This practice covers methods of extraction of medical plastics and may be applicable to other materials. This practice identifies a method for obtaining “extract liquid” for use in determining the biological response in preclinical testing. Further testing of the “extract liquid” is specified in other ASTM standards. The extract may undergo chemical analysis as part of the preclinical evaluation of the biological response, and the material after extraction may also be examined. 1.2 This practice may be used for, but is not limited to the following areas: partial evaluation of raw materials, auditing materials within the manufacturing process, and testing final products. This practice may also be used as a referee method for the measurement of extractables in plastics used in medical devices. 1.3 1.3 This practice was initially developed for extraction of medical plastics not intended to undergo degradation or absorption during normal medical device usage. When applied to the extraction of absorbable materials, additional considerations may be necessary in the selection of extraction procedures and fluids. 1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. |
| 국제분류(ICS)코드 | |
| 페이지수 | 4 |
| Edition | 14 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM F619-20 | Standard Practice for Extraction of Materials Used in Medical Devices | 2020-08-01 | 표준 |
| 2 | ASTM F619-20 REDLINE | Standard Practice for Extraction of Materials Used in Medical Devices | 2020-08-01 | 표준 |
| 3 | ASTM F619-14 | Standard Practice for Extraction of Medical Plastics | 2014-03-01 | 구판 |
| 4 | ASTM F619-14 REDLINE | Standard Practice for Extraction of Medical Plastics | 2014-03-01 | 구판 |
| 5 | ASTM F619-03(2008) | Standard Practice for Extraction of Medical Plastics | 2008-08-01 | 구판 |
| 6 | ASTM F619-03 | Standard Practice for Extraction of Medical Plastics | 2003-11-01 | 구판 |
| 7 | ASTM F619-02 | Standard Practice for Extraction of Medical Plastics | 2002-04-10 | 구판 |
| 8 | ASTM F619-79(1997)e1 | Standard Practice for Extraction of Medical Plastics | 1997-12-10 | 구판 |
관련상품이 존재하지 않습니다.
ASTM F2477-19 REDLINE - Standard Test Methods for
ASTM E3231-19 - Standard Guide for Cell Culture Growth Assessment of Single-Use Material 상세보기
ASTM F2077-18 - Test Methods For Intervertebral Body Fusion Devices 상세보기
ASTM F2267-04(2018) - Standard Test Method for Measuring Load Induced Subsidence of Intervertebral Body Fusion Device Under Static Axial Compression 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
