관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
표준
판매
Standard Test Methods for Tension Testing of Metallic Materials
| 분야 | 03.01 : 금속-기계적 시험;가열 및 저온시험;금속 조직학 |
|---|---|
| 적용범위 | 1.1?These test methods cover the tension testing of metallic materials in any form at room temperature, specifically, the methods of determination of yield strength, yield point elongation, tensile strength, elongation, and reduction of area. 1.2?The gauge lengths for most round specimens are required to be 4D for E8 and 5D for E8M. The gauge length is the most significant difference between E8 and E8M test specimens. Test specimens made from powder metallurgy (P/M) materials are exempt from this requirement by industry-wide agreement to keep the pressing of the material to a specific projected area and density. 1.3?Exceptions to the provisions of these test methods may need to be made in individual specifications or test methods for a particular material. For examples, see Test Methods and Definitions A370 and Test Methods B557, and B557M. 1.4?Room temperature shall be considered to be 10?°C to 38?°C [50?°F to 100°F] unless otherwise specified. 1.5?The values stated in SI units are to be regarded as separate from inch/pound units. The values stated in each system are not exact equivalents; therefore each system must be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.6?This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.7?This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
| 국제분류(ICS)코드 | 77.040.10 : 금속의 기계적 시험 |
| 페이지수 | 35 |
| Edition | 24 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM E8/E8M-24 | Standard Test Methods for Tension Testing of Metallic Materials | 2024-01-01 | 표준 |
| 2 | ASTM E8/E8M-24 REDLINE | Standard Test Methods for Tension Testing of Metallic Materials | 2024-01-01 | 표준 |
| 3 | ASTM E8/E8M-22 | Standard Test Methods for Tension Testing of Metallic Materials | 2022-05-01 | 구판 |
| 4 | ASTM E8/E8M-22 REDLINE | Standard Test Methods for Tension Testing of Metallic Materials | 2022-05-01 | 구판 |
| 5 | ASTM E8/E8M-21 | Standard Test Methods for Tension Testing of Metallic Materials | 2021-02-01 | 구판 |
| 6 | ASTM E8/E8M-21 REDLINE | Standard Test Methods for Tension Testing of Metallic Materials | 2021-02-01 | 구판 |
| 7 | ASTM E8/E8M-16ae1 | Standard Test Methods for Tension Testing of Metallic Materials | 2016-08-01 | 구판 |
| 8 | ASTM E8/E8M-16a REDLINE | Standard Test Methods for Tension Testing of Metallic Materials | 2016-08-01 | 구판 |
| 9 | ASTM E8/E8M-16a | Standard Test Methods for Tension Testing of Metallic Materials | 2016-08-01 | 구판 |
| 10 | ASTM E8/E8M-16 | Standard Test Methods for Tension Testing of Metallic Materials | 2016-07-15 | 구판 |
| 11 | ASTM E8/E8M-15a | Standard Test Methods for Tension Testing of Metallic Materials | 2015-05-01 | 구판 |
| 12 | ASTM E8/E8M-15 | Standard Test Methods for Tension Testing of Metallic Materials | 2015-02-01 | 구판 |
| 13 | ASTM E8/E8M-13a | Standard Test Methods for Tension Testing of Metallic Materials | 2013-07-01 | 구판 |
| 14 | ASTM E8/E8M-13 | Standard Test Methods for Tension Testing of Metallic Materials | 2013-06-01 | 구판 |
| 15 | ASTM E8/E8M-11 | Standard Test Methods for Tension Testing of Metallic Materials | 2011-12-01 | 구판 |
| 16 | ASTM E8/E8M-09 | Standard Test Methods for Tension Testing of Metallic Materials | 2009-12-01 | 구판 |
| 17 | ASTM E8/E8M-08 | Standard Test Methods for Tension Testing of Metallic Materials | 2008-02-01 | 구판 |
관련상품이 존재하지 않습니다.
ASTM E23-24 - Standard Test Methods for Notched Bar Impact Testing of Metallic Materials 상세보기
ASTM E10-23 - Standard Test Method for Brinell Hardness of Metallic Materials 상세보기
ASTM E18-24 - Standard Test Methods for Rockwell Hardness of Metallic Materials 상세보기
ASTM E92-23 - Standard Test Methods for Vickers Hardness and Knoop Hardness of Metallic Materials 상세보기
ASTM A276/A276M-24 - Standard Specification for Stainless Steel Bars and Shapes 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
