관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
표준
판매
Standard Test Method for Measuring Changes in Height of Cylindrical Specimens of Hydraulic-Cement Grout
| 분야 | 04.02 : 콘크리트 및 골재 |
|---|---|
| 적용범위 | 1.1?This test method covers measurement of the changes in height of hydraulic-cement grout by the use of 75?mm by 150?mm [3?in. by 6?in.] cylinders, when the cylinders are protected so that the tendency to change in height does not include evaporation so as to cause drying, uptake of moisture, carbonation, or exposure to temperatures outside the range 23?°C ± 2.0?°C [73?°F ± 3.5?°F] or, optionally, to another specified temperature controlled within ±2.0?°C [±3.5?°F]. 1.2?If desired, this test method can be adapted to studies of changes in height involving either schedules or environmental treatment different from the standard procedures prescribed by this test method. 1.3?The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. Note 1:?Sieve size is identified by its standard designation in Specification E11. The alternative designation given in parentheses is for information only and does not represent a different standard sieve size. 1.4?The text of this standard references notes and footnotes that provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of this standard. 1.5?This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. (Warning?Fresh hydraulic cementitious mixtures are caustic and may cause chemical burns to exposed skin and tissue upon prolonged exposure.2) 1.6?This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
| 국제분류(ICS)코드 | 91.100.10 : 시멘트. 석고. 모르타르 |
| 페이지수 | 6 |
| Edition | 23 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM C1090/C1090M-23 | Standard Test Method for Measuring Changes in Height of Cylindrical Specimens of Hydraulic-Cement Grout | 2023-06-15 | 표준 |
| 2 | ASTM C1090/C1090M-23 REDLINE | Standard Test Method for Measuring Changes in Height of Cylindrical Specimens of Hydraulic-Cement Grout | 2023-06-15 | 표준 |
| 3 | ASTM C1090/C1090M-15 REDLINE | Standard Test Method for Measuring Changes in Height of Cylindrical Specimens of Hydraulic-Cement Grout | 2015-12-15 | 구판 |
| 4 | ASTM C1090/C1090M-15 | Standard Test Method for Measuring Changes in Height of Cylindrical Specimens of Hydraulic-Cement Grout | 2015-12-15 | 구판 |
관련상품이 존재하지 않습니다.
ASTM C940-22 - Standard Test Method for Expansion and Bleeding of Freshly Mixed Grouts for Preplaced-Aggregate Concrete in the Laboratory 상세보기
ASTM C939/C939M-22 - Standard Test Method for Flow of Grout for Preplaced-Aggregate Concrete (Flow Cone Method) 상세보기
ASTM C827/C827M-23 - Standard Test Method for Change in Height at Early Ages of Cylindrical Specimens of Cementitious Mixtures 상세보기
ASTM D545-23 - Standard Test Methods for Preformed Expansion Joint Fillers for Concrete Construction (Nonextruding and Resilient Types) 상세보기
ASTM C109/C109M-23 - Standard Test Method for Compressive Strength of Hydraulic Cement Mortars (Using 50?mm [2 in.] Cube Specimens) 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
