관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
표준
판매
Standard Specification for Polyolefin Pipe and Fittings for Corrosive Waste Drainage Systems
| 분야 | 08.04 : 플라스틱 파이프 및 건축용 제품 |
|---|---|
| 적용범위 | 1.1?This specification covers requirements for non-pressure polyolefin pipe and fittings for corrosive waste drainage systems. 1.2?Pipe is produced in Schedule 40 and 80 IPS sizes, and in DR IPS sizes for two polyolefins, polyethylene (PE) and polypropylene (PP). 1.3?The interchangeability of pipe and fittings made by different manufacturers is not addressed in this specification. Transition fittings for joining pipe and fittings of different manufacturers is provided for in this specification. 1.4?Pipe and fittings are joined by the heat fusion method ( Practice D2657 for PP butt and saddle fusion, Practice F2620 for PE butt, saddle and socket fusion and Practice F1290 for polyolefin electrofusion) or by using mechanical joints recommended by the manufacturer. 1.5?The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.6?The following safety hazards caveat pertains only to the test method, Section 8, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.7?This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
| 국제분류(ICS)코드 | 23.040.20 : 플라스틱 파이프 |
| 페이지수 | 7 |
| Edition | 22 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM F1412-22 | Standard Specification for Polyolefin Pipe and Fittings for Corrosive Waste Drainage Systems | 2022-11-01 | 표준 |
| 2 | ASTM F1412-22 REDLINE | Standard Specification for Polyolefin Pipe and Fittings for Corrosive Waste Drainage Systems | 2022-11-01 | 표준 |
| 3 | ASTM F1412-16 | Standard Specification for Polyolefin Pipe and Fittings for Corrosive Waste Drainage Systems | 2016-02-01 | 구판 |
| 4 | ASTM F1412-16 REDLINE | Standard Specification for Polyolefin Pipe and Fittings for Corrosive Waste Drainage Systems | 2016-02-01 | 구판 |
| 5 | ASTM F1412-09 | Standard Specification for Polyolefin Pipe and Fittings for Corrosive Waste Drainage Systems | 2009-01-15 | 구판 |
| 6 | ASTM F1412-01e1 | Standard Specification for Polyolefin Pipe and Fittings for Corrosive Waste Drainage Systems | 2001-04-10 | 구판 |
| 7 | ASTM F1412-00 | Standard Specification for Polyolefin Pipe and Fittings for Corrosive Waste Drainage Systems | 2001-04-10 | 구판 |
| 8 | ASTM F1412-01 | Standard Specification for Polyolefin Pipe and Fittings for Corrosive Waste Drainage Systems | 2001-04-10 | 구판 |
관련상품이 존재하지 않습니다.
ISO 9624:2019 - Thermoplastics piping systems for fluids under pressure — Flange adapters and loose backing flanges — Mating dimensions 상세보기
ISO 13760:1998 - Plastics pipes for the conveyance of fluids under pressure — Miner's rule — Calculation method for cumulative damage 상세보기
ASTM F3565-23 - Standard Practice for Electrofusion Joining Polyethylene (PE) Pipe and Fittings for Pressure Pipe Service 상세보기
ASTM F1055-16a(2022) - Standard Specification for Electrofusion Type Polyethylene Fittings for Outside Diameter Controlled Polyethylene and Crosslinked Polyethylene (PEX) Pipe and Tubing 상세보기
ASTM F2807-13(2018) - Standard Specification for Multilayer Polyethylene-Polyamide (PE-PA) Pipe for Pressure Piping Applications (Withdrawn 2024) 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
