관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
표준
판매
Standard Specification for Vertiport Design
| 분야 | 15.09 : 종이, 회사 이미지용 상품 |
|---|---|
| 적용범위 | 1.1?This specification defines the requirements for the planning, design, and establishment of vertiports intended to service vertical takeoff and landing (VTOL) aircraft. These aircraft include, but are not limited to, standard category aircraft, optionally piloted aircraft, and unmanned aircraft. Aircraft not covered by this specification include VTOL aircraft less than 55?lb [25?kg]. In developing these standards, identified types of eVTOL aircraft, for example, Multi-Rotor, Lift & Cruise, Vectored Thrust, Tilt Wing, Tilt Rotor, etc., were considered. Ultimately it is up to the authorities having jurisdiction (AHJ) as to how and to what extent these standards are applied. Vertiports may provide commercial or private services in support of the operation of eVTOL aircraft including, but not limited to, some or all of occupant and cargo transport, air medical, flight instruction, aerial work, aircraft rental, fueling, charging of energy storage devices, battery exchange, hangaring, and maintenance services. 1.2?This specification is intended to support the design of civil vertiports and vertistops, however, it may also be used as a best practice document for other facilities. 1.2.1?Vertiport? is a generic reference to the area of land, water, or structure used, or intended to be used, for the landing and takeoff of VTOL aircraft, together with associated buildings and facilities. At this time, aircraft with floats conducting water landings and takeoffs are not included in this specification. 1.2.2?Vertistop?The same as Vertiport, except that no fueling, defueling, scheduled maintenance, scheduled repairs, or storage of aircraft is permitted. Unscheduled maintenance and repairs to return an aircraft in an AOG (Aircraft on Ground) status to a serviceable status are permissible. 1.3?This document may present information in either SI units, English Engineering units, or both. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined 1.4?This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5?This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
| 국제분류(ICS)코드 | |
| 페이지수 | 11 |
| Edition | 22 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM F3423/F3423M-22 | Standard Specification for Vertiport Design | 2022-07-01 | 표준 |
관련상품이 존재하지 않습니다.
ASTM F2910-22 - Standard Specification for Design and Construction of a Small Unmanned Aircraft System (sUAS) 상세보기
ASTM F2851-10(2018) - Standard Practice for UAS Registration and Marking (Excluding Small Unmanned Aircraft Systems) 상세보기
ASTM F3298-19 - Standard Specification for Design, Construction, and Verification of Lightweight Unmanned Aircraft Systems (UAS) 상세보기
ASTM F3478-20 - Standard Practice for Development of a Durability and Reliability Flight Demonstration Program for Low-Risk Unmanned Aircraft Systems (UAS) under FAA Oversight 상세보기
ASTM F3548-21 - Standard Specification for UAS Traffic Management (UTM) UAS Service Supplier (USS) Interoperability 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
