관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
표준
판매
Standard Specification for Solid Round Glass Fiber Reinforced Polymer Bars for Concrete Reinforcement
| 분야 | 15.03 : 공간시물레이션; 항공우주재료; 고율섬유와 합성물 |
|---|---|
| 적용범위 | 1.1?This specification covers glass fiber reinforced polymer (GFRP) bars, provided in cut lengths and bent shapes and having an external surface enhancement for concrete reinforcement. Bars covered by this specification shall meet the requirements for geometric, material, mechanical, and physical properties described herein. 1.2?Bars produced according to this standard are qualified using the test methods and must meet the requirements given by Table 1. Quality control and certification of production lots of bars are completed using the test methods and must meet the requirements given in Table 2. 1.3?The text of this specification references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables) shall not be considered as requirements of the specification. 1.4?The following FRP materials are not covered by this specification: 1.4.1?Bars made of more than one load-bearing fiber type (that is, hybrid FRP). 1.4.2?Bars having no external surface enhancement (that is, plain or smooth bars, or dowels). 1.4.3?Bars with geometries other than solid, round cross sections. 1.4.4?Pre-manufactured grids and gratings made with FRP materials. 1.5?This specification is applicable for either SI (as Specification D7957M) or inch-pound units (as Specification D7957). 1.6?Units?The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. 1.7?This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.8?This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
| 국제분류(ICS)코드 | 91.100.30 : 콘크리트 및 콘크리트 제품 |
| 페이지수 | 5 |
| Edition | 22 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM D7957/D7957M-22 | Standard Specification for Solid Round Glass Fiber Reinforced Polymer Bars for Concrete Reinforcement | 2022-02-01 | 표준 |
| 2 | ASTM D7957/D7957M-22 REDLINE | Standard Specification for Solid Round Glass Fiber Reinforced Polymer Bars for Concrete Reinforcement | 2022-02-01 | 표준 |
| 3 | ASTM D7957/D7957M-17 | Standard Specification for Solid Round Glass Fiber Reinforced Polymer Bars for Concrete Reinforcement | 2017-08-01 | 구판 |
관련상품이 존재하지 않습니다.
ASTM D7205/D7205M-21 - Standard Test Method for Tensile Properties of Fiber Reinforced Polymer Matrix Composite Bars 상세보기
ASTM D7913/D7913M-14(2020) - Standard Test Method for Bond Strength of Fiber-Reinforced Polymer Matrix Composite Bars to Concrete by Pullout Testing 상세보기
ASTM D578/D578M-18 - Standard Specification for Glass Fiber Strands 상세보기
ASTM D7617/D7617M-11(2017) - Standard Test Method for Transverse Shear Strength of Fiber-reinforced Polymer Matrix Composite Bars 상세보기
ASTM D7028-07(2015) - Standard Test Method for Glass Transition Temperature (DMA Tg) of Polymer Matrix Composites by Dynamic Mechanical Analysis (DMA) 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
