관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
표준
판매
Standard Test Method for Abrasion Resistance of Horizontal Concrete Surfaces
| 분야 | 04.02 : 콘크리트 및 골재 |
|---|---|
| 적용범위 | 1.1 This test method covers three procedures for determining the relative abrasion resistance of horizontal concrete surfaces. The procedures differ in the type and degree of abrasive force they impart, and are intended for use in determining variations in surface properties of concrete affected by mixture proportions, finishing, and surface treatment. They are not intended to provide a quantitative measurement of the length of service that may be expected from a specific surface. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the inch-pound units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of each other. 1.3 The text of this standard references notes and footnotes that provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of this standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. (Warning—Fresh hydraulic cementitious mixtures are caustic and may cause chemical burns to skin and tissue upon prolonged exposure.2) Note 1: Other procedures are available for measuring the abrasion resistance of concrete surfaces in addition to the three procedures contained in this test method. Consideration should be given to Test Methods C944/C944M and C418. The test method most closely representing service conditions should be used. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
| 국제분류(ICS)코드 | 91.100.30 : 콘크리트 및 콘크리트 제품 |
| 페이지수 | 6 |
| Edition | 19 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM C779/C779M-19 | Standard Test Method for Abrasion Resistance of Horizontal Concrete Surfaces | 2019-10-01 | 표준 |
| 2 | ASTM C779/C779M-19 REDLINE | Standard Test Method for Abrasion Resistance of Horizontal Concrete Surfaces | 2019-10-01 | 표준 |
| 3 | ASTM C779/C779M-12 REDLINE | Standard Test Method for Abrasion Resistance of Horizontal Concrete Surfaces | 2012-12-01 | 구판 |
| 4 | ASTM C779/C779M-12 | Standard Test Method for Abrasion Resistance of Horizontal Concrete Surfaces | 2012-12-01 | 구판 |
| 5 | ASTM C779/C779M-05(2010) | Standard Test Method for Abrasion Resistance of Horizontal Concrete Surfaces | 2010-10-01 | 구판 |
| 6 | ASTM C779/C779M-05 | Standard Test Method for Abrasion Resistance of Horizontal Concrete Surfaces | 2005-12-15 | 구판 |
| 7 | ASTM C779/C779M-00 | Standard Test Method for Abrasion Resistance of Horizontal Concrete Surfaces | 2000-06-10 | 구판 |
관련상품이 존재하지 않습니다.
ASTM C1581/C1581M-18a - Standard Test Method for Determining Age at Cracking and Induced Tensile Stress Characteristics of Mortar and Concrete under Restrained Shrinkage 상세보기
KS F 2424 - 모르타르 및 콘크리트의 길이 변화 시험 방법 상세보기
KS F 2762 - 콘크리트 보수ㆍ보호재의 접착 강도 시험 방법 상세보기
KS F 2405(2017 확인) - 콘크리트 압축 강도 시험방법 상세보기
KS F 2438 - 콘크리트 원주 공시체의 정탄성 계수 및 포아송비 시험 방법 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
