관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
표준
판매
Standard Practice for Sampling Aggregates
| 분야 | 04.03 : 도로 및 포장용 재료; 자동차-포장도로시스템 |
|---|---|
| 적용범위 | 1.1 This practice covers sampling of coarse and fine aggregates for the following purposes: 1.1.1 Preliminary investigation of the potential source of supply, 1.1.2 Control of the product at the source of supply, 1.1.3 Control of the operations at the site of use, and 1.1.4 Acceptance or rejection of the materials. Note 1: Sampling plans and acceptance and control tests vary with the type of construction in which the material is used. 1.2 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard. 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. Note 2: The quality of the results produced by this standard are dependent on the competence of the personnel performing the procedure and the capability, calibration, and maintenance of the equipment used. Agencies that meet the criteria of Specification D3666 are generally considered capable of competent and objective testing, sampling, inspection, etc. Users of this standard are cautioned that compliance with Specification D3666 alone does not completely ensure reliable results. Reliable results depend on many factors; following the suggestions of Specification D3666 or some similar acceptable guideline provides a means of evaluating and controlling some of those factors. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
| 국제분류(ICS)코드 | 91.100.30 : 콘크리트 및 콘크리트 제품 |
| 페이지수 | 7 |
| Edition | 19 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM D75/D75M-19 | Standard Practice for Sampling Aggregates | 2019-11-01 | 표준 |
| 2 | ASTM D75/D75M-19 REDLINE | Standard Practice for Sampling Aggregates | 2019-11-01 | 표준 |
| 3 | ASTM D75/D75M-14 REDLINE | Standard Practice for Sampling Aggregates | 2014-06-01 | 구판 |
| 4 | ASTM D75/D75M-14 | Standard Practice for Sampling Aggregates | 2014-06-01 | 구판 |
| 5 | ASTM D75/D75M-13 | Standard Practice for Sampling Aggregates | 2013-12-15 | 구판 |
| 6 | ASTM D75/D75M-09 | Standard Practice for Sampling Aggregates | 2009-06-01 | 구판 |
관련상품이 존재하지 않습니다.
AD 2000-MERKBLATT W 0:2023-08 - Materials for pressure vessels - General principles for materials 상세보기
AD 2000-MERKBLATT W 1:2020-04 - Flat products of unalloyed and alloy steels 상세보기
SEP 1390:1996-07 - Im DIN-Anzeiger für technische Regeln 9/2008, ICS 77.040.10, wurde das Dokument irrtümlich als zurückgezogen gemeldet. Das Dokument ist weiterhin gültig. 상세보기
ASTM D7843 - 21 - Standard Test Method for Measurement of Lubricant Generated Insoluble Color Bodies in In-Service Turbine Oils using Membrane Patch Colorimetry 상세보기
AS 1397-2011/Amdt 1-2012 - Continuous hot-dip metallic coated steel sheet and strip - Coatings of zinc and zinc alloyed with aluminium and magnesium 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
