관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
표준
판매
Standard Test Methods for Rigid Sheet and Plate Materials Used for Electrical Insulation
| 분야 | 10.01 : 전기절연 (Ⅰ) | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 적용범위 | 1.1 These test methods cover procedures for testing rigid electrical insulation normally manufactured in flat sheet or plate form. They are generally used as terminal boards, spacers, voltage barriers, and circuit boards. 1.2 Use Test Methods D619 (withdrawn) or Specification D710 for tests applying to vulcanized fibre. 1.3 Some of the test methods contained in this standard are similar to those contained in IEC 60893-2, which applies to rigid industrial laminated sheets based on thermosetting resins for electrical purposes. 1.4 The test methods appear in the following sections:
1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.6 This is a fire-test-response standard. See Sections 61 through 74, which are the procedures for assessing ignitability and burning time under specific test conditions 1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements are given in 31.1 and 1.8. 1.8 This standard measures and describes the response of materials, products, or assemblies to heat and flame under controlled conditions, but does not by itself incorporate all factors required for fire hazard or fire risk assessment of the materials, products, or assemblies under actual fire conditions. 1.9 Fire testing is inherently hazardous. Adequate safeguards for personnel and property shall be employed in conducting these tests. 1.10 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| 국제분류(ICS)코드 | 29.035.01 : 일반 절연 재료 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| 페이지수 | 18 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| Edition | 19e1 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM D229-19 | Standard Test Methods for Rigid Sheet and Plate Materials Used for Electrical Insulation | 2019-03-01 | 구판 |
| 2 | ASTM D229-19e1 | Standard Test Methods for Rigid Sheet and Plate Materials Used for Electrical Insulation | 2019-03-01 | 표준 |
| 3 | ASTM D229-13 | Standard Test Methods for Rigid Sheet and Plate Materials Used for Electrical Insulation | 2013-11-01 | 구판 |
| 4 | ASTM D229-13 REDLINE | Standard Test Methods for Rigid Sheet and Plate Materials Used for Electrical Insulation | 2013-11-01 | 구판 |
| 5 | ASTM D229-09b | Standard Test Methods for Rigid Sheet and Plate Materials Used for Electrical Insulation | 2009-10-01 | 구판 |
| 6 | ASTM D229-09a | Standard Test Methods for Rigid Sheet and Plate Materials Used for Electrical Insulation | 2009-06-01 | 구판 |
| 7 | ASTM D229-09 | Standard Test Methods for Rigid Sheet and Plate Materials Used for Electrical Insulation | 2009-01-15 | 구판 |
| 8 | ASTM D229-96 | Standard Test Methods for Rigid Sheet and Plate Materials Used for Electrical Insulation | 2001-11-10 | 구판 |
| 9 | ASTM D229-01 | Standard Test Methods for Rigid Sheet and Plate Materials Used for Electrical Insulation | 2001-11-10 | 구판 |
관련상품이 존재하지 않습니다.
ASTM D714-02(2017) - Standard Test Method for Evaluating Degree of Blistering of Paints 상세보기
ISO 1183-1:2019 - Plastics — Methods for determining the density of non-cellular plastics — Part 1: Immersion method, liquid pycnometer method and titration method 상세보기
ISO 527-1:2019 - Plastics — Determination of tensile properties — Part 1: General principles 상세보기
ASTM D651(1984 Edition) - STANDARD TEST METHOD FOR TENSILE STRENGTH OF MOLDED ELECTRICAL INSULATING MATERIALS 상세보기
ASTM D3431(1987 Edition) - STANDARD TEST METHOD FOR TRACE NITROGEN IN LIQUID PETROLEUM HYDROCARBONS (MICROCOULOMETRIC METHOD) 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
