관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
표준
판매
Standard Specification for Through-Thickness Tension Testing of Steel Plates for Special Applications
| 분야 | 01.04 : 철강-구조물, 보강재, 압력용기, 철도 |
|---|---|
| 적용범위 | 1.1 This specification2 covers the procedures and acceptance standards for the determination of reduction of area using a tension test specimen whose axis is perpendicular to the rolled surfaces of steel plates 1 in. [25 mm] and greater in thickness. The principal purpose of the testing is to provide a measure of the resistance of a steel plate to lamellar tearing. (See Appendix X1.) 1.2 The values stated in either inch-pound units or SI units are to be regarded as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the specification. 1.3 This specification is expressed in both inch-pound and SI units. However, unless the order specifies the applicable “M” specification designation (SI units), the material shall be furnished to inch-pound units. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
| 국제분류(ICS)코드 | |
| 페이지수 | 5 |
| Edition | 03(2018) |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM A770/A770M-03(2018) | Standard Specification for Through-Thickness Tension Testing of Steel Plates for Special Applications | 2018-09-01 | 표준 |
| 2 | ASTM A770/A770M-03(2012)e1 | Standard Specification for Through-Thickness Tension Testing of Steel Plates for Special Applications | 2012-03-01 | 구판 |
| 3 | ASTM A770/A770M-03(2012) | Standard Specification for Through-Thickness Tension Testing of Steel Plates for Special Applications | 2012-03-01 | 구판 |
| 4 | ASTM A770/A770M-03(2007) | Standard Specification for Through-Thickness Tension Testing of Steel Plates for Special Applications | 2007-11-01 | 구판 |
| 5 | ASTM A770/A770M-03 | Standard Specification for Through-Thickness Tension Testing of Steel Plates for Special Applications | 2003-05-10 | 구판 |
| 6 | ASTM A770/A770M-86(1996) | Standard Specification for Through-Thickness Tension Testing of Steel Plates for Special Applications | 2001-01-01 | 구판 |
| 7 | ASTM A770/A770M-86(2001) | Standard Specification for Through-Thickness Tension Testing of Steel Plates for Special Applications | 2001-01-01 | 구판 |
관련상품이 존재하지 않습니다.
DVS 3320-2:2019-01 - Quality requirements for the use of pressure sensitive adhesive tape for permanent bonded joints 상세보기
DVS 3320-1:2012-02 - Quality requirements in adhesive application 상세보기
AGMA 6015 Revision A13, September 23, 2013 - Power Rating of Single and Double Helical Gearing for Rolling Mill Service 상세보기
GOST 19904-90 - Cold-rolled steel sheets. Dimensions 상세보기
GOST 16523-97 - Rolled sheets from quality and ordinary carbon steel for general purposes. Specifications 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
