관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
구판
판매
Standard Test Method for Failure in Sewn Seams of Woven Fabrics
| 분야 | 07.01 : 섬유(Ⅰ) |
|---|---|
| 적용범위 | 1.1 This test method measures the sewn seam strength in woven fabrics by applying a force perpendicular to the sewn seams. 1.1.1 The axis perpendicular to the sewn seam can represent either the warp yarn axis or filling yarn axis, the same axis tested when using grab Test Method D5034. 1.1.1.1 This test method is applicable to sewn seams obtained from a previously sewn article or seams sewn with fabric samples using one of two specific seam assemblies as shown in Table 1. (A) A complete description of seam types and stitch types can be found in Practice D6193. Note 1: When the performance of a woven textile structure requires data to indicate the maximum seam strength that will result in the failure of fabric on either side of seam, the standard seam can be changed to use the Lapped seam type construction with two or more rows of stitching: Lsc-2; Lsc-3; Lsc-4; and the maximum number of stitches per inch that can be used. (See Practice D6193.) 1.2 This test method is used when the maximum breaking force measurement to rupture of a woven fabric sewn seam is required. 1.2.1 This test method is used when the seam efficiency measurement of a woven fabric sewn seam is required. 1.2.2 This test method is used to identify the sewn seam strength threshold at which the failure of the stitching occurs, without damage to the fabric, so that the textile product can be repaired. 1.2.3 This test method is used to identify the force at which seam strength results in slippage and displacement of warp yarns, filling yarns, or any combination of these yarns. 1.3 This test method does not predict actual wear performance of a seam. 1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
| 국제분류(ICS)코드 | 59.080.30 : 직물류 |
| 페이지수 | 15 |
| Edition | 17(2018) |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM D1683/D1683M-22 | Standard Test Method for Failure in Sewn Seams of Woven Fabrics | 2022-04-01 | 표준 |
| 2 | ASTM D1683/D1683M-22 REDLINE | Standard Test Method for Failure in Sewn Seams of Woven Fabrics | 2022-04-01 | 표준 |
| 3 | ASTM D1683/D1683M-17(2018) | Standard Test Method for Failure in Sewn Seams of Woven Fabrics | 2018-03-15 | 구판 |
| 4 | ASTM D1683/D1683M-17e1 | Standard Test Method for Failure in Sewn Seams of Woven Fabrics | 2017-03-01 | 구판 |
| 5 | ASTM D1683/D1683M-17 | Standard Test Method for Failure in Sewn Seams of Woven Fabrics | 2017-03-01 | 구판 |
| 6 | ASTM D1683/D1683M-16 | Standard Test Method for Failure in Sewn Seams of Woven Fabrics | 2016-11-01 | 구판 |
| 7 | ASTM D1683/D1683M-11a | Standard Test Method for Failure in Sewn Seams of Woven Apparel Fabrics | 2011-07-01 | 구판 |
| 8 | ASTM D1683/D1683M-11 | Standard Test Method for Failure in Sewn Seams of Woven Apparel Fabrics | 2011-02-01 | 구판 |
관련상품이 존재하지 않습니다.
ISO 2411:2017 - Rubber- or plastics-coated fabrics — Determination of coating adhesion 상세보기
ISO 1421:2016 - Rubber- or plastics-coated fabrics — Determination of tensile strength and elongation at break 상세보기
ASTM D5034-09(2017) - Standard Test Method for Breaking Strength and Elongation of Textile Fabrics (Grab Test) 상세보기
ASTM D4329-13 - Standard Practice for Fluorescent Ultraviolet (UV) Lamp Apparatus Exposure of Plastics 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
