관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
표준
판매
Standard Specification for Laboratory Glass Volumetric Flasks
| 분야 | 14.04 : 시험소 기계 장치; 재료의 퇴화; 여과; SI; 화재 안전 |
|---|---|
| 적용범위 | 1.1 This specification covers requirements for glass volumetric flasks of precision and general-purpose grades suitable for laboratory purposes. 1.1.1 Class A—Each flask of precision grade shall be marked with the letter “A” to signify compliance with applicable construction and accuracy requirements. Flasks may be marked with an identification number (serial number) at the option of the manufacturer. 1.1.2 Class B—General purpose flasks are of the same basic design as Class A flasks. However, volumetric tolerances for Class B flasks shall be within twice the specified range allowed for Class A flasks. These flasks need not be marked with their class designation. Note 1: Specifications for micro volumetric flasks in sizes from 1 mL to 25 mL, inclusive, are given in Specification E237. Note 2: The Twelfth General (International) Conference on Weights and Measures redefined the litre as a “special name for the cubic decimetre,” but agreed to permit continuance of the terms litre, millilitre, and mL, except in association with measurements of the highest precision. For volumetric glassware the difference between the old and new meanings of litre is negligible. Therefore, either mL or cm3 may be marked on ware covered by this Specification. 1.1.3 Special Size Flasks—Precision grade flasks may be manufactured with nominal capacities not listed in this standard. Such flasks shall be considered “Class A” flasks, provided they meet the accuracy tolerance of the next largest “Class A” flask appearing in Table 1 and comply with the marking requirements of 1.1.1. 1.1.4 Wide-Mouth Flasks—Requirements for insertion of tablets or capsules for assay dilution and to accommodate access of larger diameter pipets require volumetric flasks with larger necks. These flasks appear in Table 2. These flasks shall conform to the marking requirements of 1.1.1. Additionally, the accuracy tolerance shall be marked on each “Class A” wide-mouth flask. 1.1.5 Special Size Wide-Mouth Flasks—Precision grade wide-mouth flasks may be manufactured with nominal capacities not listed in this standard. Such flasks shall be considered “Class A” flasks provided they meet the accuracy tolerance of the next largest “Class A” wide-mouth flask appearing in Table 2 and the marking requirements of 1.1.4. 1.2 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
| 국제분류(ICS)코드 | |
| 페이지수 | 3 |
| Edition | 10(2017) |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM E288-10(2017) | Standard Specification for Laboratory Glass Volumetric Flasks | 2017-11-01 | 표준 |
| 2 | ASTM E288-10 | Standard Specification for Laboratory Glass Volumetric Flasks | 2010-04-01 | 구판 |
| 3 | ASTM E288-06 | Standard Specification for Laboratory Glass Volumetric Flasks | 2006-04-01 | 구판 |
| 4 | ASTM E288-03 | Standard Specification for Laboratory Glass Volumetric Flasks | 2003-01-10 | 구판 |
| 5 | ASTM E288-94(1998) | Standard Specification for Laboratory Glass Volumetric Flasks | 1998-10-10 | 구판 |
관련상품이 존재하지 않습니다.
ASTM D5489-18 - Standard Guide for Care Symbols for Care Instructions on Textile Products 상세보기
ASTM E1154-14 - Standard Specification for Piston or Plunger Operated Volumetric Apparatus 상세보기
ASTM E1272-02(2012) - Standard Specification for Laboratory Glass Graduated Cylinders 상세보기
ASTM E969-02(2012) - Standard Specification for Glass Volumetric (Transfer) Pipets 상세보기
ASTM E542-01(2012) - Standard Practice for Calibration of Laboratory Volumetric Apparatus 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
