관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
구판
판매
Standard Test Method of Measuring Shrinkage from Mold Dimensions of Thermoplastics
| 분야 | 08.01 : 플라스틱 (Ⅰ) |
|---|---|
| 적용범위 | 1.1 This test method is intended to measure shrinkage from mold cavity to molded dimensions of thermoplastics when molded by compression or injection processes with specified process conditions. 1.2 This test method covers shrinkage measurements at 24 and 48 hours. 1.3 This method will give comparable data based on standard specimens and can not predict absolute values in actual molded parts with varying flow paths, wall thicknesses, pressure and temperature gradients and process conditions. Differences in mold shrinkage may also be observed among the three specimen geometries described in this test method. 1.4 The values stated in SI units are to be regarded as the standard. The values given in parentheses are given for information only. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Note 1: This standard and ISO 294-3 are equivalent in the design of specimen D2. This test method is equivalent to ISO 294-4 where Type D2 specimens and the procedure in Appendix X2 are used. |
| 국제분류(ICS)코드 | 83.140.10 : 필름 및 시트 |
| 페이지수 | 8 |
| Edition | 08(2014) |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM D955-21 | Standard Test Method of Measuring Shrinkage from Mold Dimensions of Thermoplastics | 2021-04-01 | 표준 |
| 2 | ASTM D955-21 REDLINE | Standard Test Method of Measuring Shrinkage from Mold Dimensions of Thermoplastics | 2021-04-01 | 표준 |
| 3 | ASTM D955-08(2014) | Standard Test Method of Measuring Shrinkage from Mold Dimensions of Thermoplastics | 2014-08-01 | 구판 |
| 4 | ASTM D955-08 | Standard Test Method of Measuring Shrinkage from Mold Dimensions of Thermoplastics | 2008-11-01 | 구판 |
| 5 | ASTM D955-89(1996) | Standard Test Method of Measuring Shrinkage from Mold Dimensions of Thermoplastics | 2000-11-10 | 구판 |
| 6 | ASTM D955-00 | Standard Test Method of Measuring Shrinkage from Mold Dimensions of Thermoplastics | 2000-11-10 | 구판 |
관련상품이 존재하지 않습니다.
ASTM D638-14 - Standard Test Method for Tensile Properties of Plastics 상세보기
ASTM D648-18 - Standard Test Method for Deflection Temperature of Plastics Under Flexural Load in the Edgewise Position 상세보기
ASTM D257-14 - Standard Test Methods for DC Resistance or Conductance of Insulating Materials 상세보기
ASTM D495-14 - Standard Test Method for High-Voltage, Low-Current, Dry Arc Resistance of Solid Electrical Insulation 상세보기
ASTM D542-14 - Standard Test Method for Index of Refraction of Transparent Organic Plastics 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
