관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
구판
판매
Standard Specification for Electroplated Engineering Nickel Coatings
| 분야 | 02.05 : 금속 및 무기질 피막, 금속분말 |
|---|---|
| 적용범위 | 1.1 This specification covers the requirements for electroplated nickel coatings applied to metal products for engineering applications. 1.2 Electroplating of nickel for engineering applications (Note 1) requires technical considerations significantly different from decorative applications because the following functional properties are important: 1.2.1 Hardness, strength, and ductility, 1.2.2 Wear resistance, 1.2.3 Load bearing characteristics, 1.2.4 Corrosion resistance, 1.2.5 Heat scaling resistance, 1.2.6 Fretting resistance, and 1.2.7 Fatigue resistance. Note 1-Functional electroplated nickel coatings usually contain about 99% nickel, and are most frequently electrodeposited from a Watts nickel bath or a nickel sulfamate bath. Typical mechanical properties of nickel electroplated from these baths, and the combined effect of bath operation and solution composition variables on the mechanical properties of the electrodeposit are given in Practice B503. When electroplated nickel is required to have higher hardnesses, greater wear resistance, certain residual stress values and certain leveling characteristics, sulfur and other substances are incorporated in the nickel deposit through the use of certain addition agents in the electroplating solution. For the effect of such additives, see Section 4 and Annex A3. Cobalt salts are sometimes added to the plating solution to produce harder nickel alloy deposits.1.3 The following hazards caveat pertains only to the Test Methods section, Section 7, of this specification: This standard does not purport to address the safety problems associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. |
| 국제분류(ICS)코드 | |
| 페이지수 | 7 |
| Edition | 97 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM B689-97(2023) | Standard Specification for Electroplated Engineering Nickel Coatings | 2023-05-01 | 표준 |
| 2 | ASTM B689-97(2018)e1 | Standard Specification for Electroplated Engineering Nickel Coatings | 2018-06-01 | 구판 |
| 3 | ASTM B689-97(2018) | Standard Specification for Electroplated Engineering Nickel Coatings | 2018-06-01 | 구판 |
| 4 | ASTM B689-97(2013) | Standard Specification for Electroplated Engineering Nickel Coatings | 2013-12-01 | 구판 |
| 5 | ASTM B689-97(2008) | Standard Specification for Electroplated Engineering Nickel Coatings | 2008-08-01 | 구판 |
| 6 | ASTM B689-97(2003) | Standard Specification for Electroplated Engineering Nickel Coatings | 2003-02-10 | 구판 |
| 7 | ASTM B689-97 | Standard Specification for Electroplated Engineering Nickel Coatings | 1997-01-01 | 구판 |
관련상품이 존재하지 않습니다.
함께 구입한 상품이 존재하지 않습니다.
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
